1/4/2023 0 Comments Cox contour for mac laptop![]() ![]() It comes with 150 hours of built-in HD storage, but Xfinity also allows you to upgrade your cloud DVR storage with or without the X1 box. The Xfinity X1 box is $8.50 per month, or $7.50 in some locations. DISH also offers over twice the amount of simultaneous recordings.ĭIRECTV Genie comes included with your regular DIRECTV plan cost, but that also means it’s subject to a price hike in the second year of your contract, so we can’t really recommend it as a better deal. If you’re looking for the best value, the DISH Hopper 3 offers twice as much HD storage as the Cox Contour Record 6 for a fraction of the price. However, while its storage is hearty and you can fill your library with a ton of shows, some competitors offer more for less. I have not seen any more errors with this client to date but want to give it a few more weeks to see if it comes back.For those binge-watchers and folks with multiperson households, the Cox Contour Record 6 is an option that makes sense. ![]() When you reply with the configuration, I will be happy to review it for you, and hopefully I will be able to provide further insight. First, I suggest changing the speed/duplex to auto, as well as changing the cable as you mentioned above. The ARP errors you are seeing are most likely a result of the input errors on the interface. Have you tried changing the ADTRAN's port to auto? The following post will explain this further: įurthermore, if you haven't already, you should disable LLDP on the ADTRAN's WAN interface, because most cable modems do not support this protocol and sometimes it can cause issues. If the cable modem is set to auto and the ADTRAN is set to 100/Full, then it will negotiate to 100/Half-duplex and could be causing the issues. #COX CONTOUR FOR MAC LAPTOP PC#Typically, cable modems are configured as auto-negotiate for speed/duplex, which would be my guess on this modem, because your PC connected without any problems, and is most likely setup as auto as well. The ADTRAN's WAN port is hardset to 100/Full. When you get a chance will you reply with the current configuration on the ADTRAN unit ( please remember to remove any information that may be sensitive to the organization)? ![]() Thank you for asking this question in the support community. Vlan 20 Ip address is 72.215.140.35, netmask is 255.255.255.192ĥ minute input rate 284592 bits/sec, 45 packets/secĥ minute output rate 70048 bits/sec, 35 packets/secħ2654 unicasts, 8267 broadcasts, 0 multicasts inputĥ5643 unicasts, 7 broadcasts, 0 multicasts output Last clearing of "show interface" counters: neverĥ minute input rate 289216 bits/sec, 46 packets/secĥ minute output rate 71056 bits/sec, 36 packets/secħ4338 unicasts, 8276 broadcasts, 4 multicasts inputĠ unknown protocol, 0 symbol errors, 0 discardsĠ no buffer, 0 overruns, 0 internal receive errorsĥ5390 unicasts, 4 broadcasts, 1105 multicasts outputĠ internal transmit errors, 0 carrier sense errors Input flow control is disabled, 0 pause frames receivedĪRP type: ARPA ARP timeout is 20 minutes Primary system configuration file is "startup-config" Primary boot system image file is ""īackup boot system image file is "" System returned to ROM by External Hard ResetĬurrent system image file is "" MarinaMGMT uptime is 0 days, 0 hours, 25 minutes, 58 seconds I am now seeing Input and CRC errors on the WAN interface (see screenshot 3 - CRC Errors) and will return to the site to run a new Shielded Ethernet cable to see if it a "Noise" issue (" Per Cisco - The presence of many CRC errors but not many collisions is an indication of excessive noise.").Īny help with the ARP errors would be greatly appreciated! I ran the debug ARP command during this condition and received a message that I have not come across before ("Packet not enqueued on VLAN 20: Current Pkt Count Exceeded") (see screenshot 1) which may be a buffer filling up issue? I also notice that when this condition is present that I see "(unresolved)" showing up in the MAC Address table for the WAN gateway IP (see screenshot 2). A reboot of the 1335 and a few minutes of waiting (usually 3-5) bring services back online. If I connect the Ethernet cable back to the 1335, using the same cable as I used on my laptop, I still cannot get internet access. My troubleshooting to date has led me to believe that this is an ARP issue based on the attached screenshots and that I can connect my laptop directly to the cable modem and get on the net without a reboot. When this issue happens I do not see any visual (LED lights) off on either piece of equipment and when I do a on the WAN interface port I see UP/UP. The "fix" is to reboot the 1335, rebooting just the Cable Modem does not restore service. I am having an intermittent (seems to happen about every 2-3 weeks) issue with my client loosing all internet connectivity (Layer 2-7) at what seem to be random times. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |